Corner balancing is a term you’ve probably heard by now if you’re even just a little familiar with motorsports and racing. If you’ve heard it before, you likely either heard it from one of two types of people: one who is serious about motorsports knowledge and car setup, or one who likes buzzwords but doesn’t have a clue what they are talking about – something quite common in the automotive industry. Just in case you don’t know what corner balancing is, or how it works, we wanted to help our audience and customers understand this commonly misunderstood principle.
Many of you reading may have installed or adjusted a set of coilovers before. You know that the height is adjustable, but there’s more to balancing a car than ensuring the fender gaps are all equal. It’s also important to ensure the weight between diagonally opposed sets of wheels is evenly distributed, which makes handling more predictable and consistent. Imagine a table with two diagonally opposed legs shorter than the other two corners – it would teeter back and forth between those short legs, while keeping all of the weight of itself on the two longer legs that are supporting it fully. The same thing concept occurs with a car, but it’s harder to see because cars rest on springs, so an improperly balanced car can still “look” normal and squarely planted on all corners, despite one diagonal carrying much more than its fair share of weight.
When corner balancing is off, the car will have completely different handling characteristics when turning one direction compared to the opposite direction, even if the setup looks symmetrical enough to make you think it should be the same both ways. An experienced driver can feel this sensation after just a short amount of time in an unbalanced car, and it can make a massive difference in racing where every tenth of a second counts. There’s a reason that professional race teams carry vehicle scales and a bunch of wood planks to level those scales. An attempt at balancing a car on uneven ground is likely worse than not balancing at all.
We should mention that the concept of concern balancing is far more critical for very stiff cars – cars with very stiff springs relative to the vehicle’s weight, and cars with very stiff chassis’. The softer the car and springs, the more these springy components “soak up” any differences in diagonal cross.
Variables like tire pressure, tire diameter, and even rolling the car back and forth to eliminate tire bind from being lowered onto scales – are critically important when it comes to finalizing your corner balance. It’s important to note that you should also set your coilovers to your preferred ride height and align the car before starting a corner balance. The adjustments of corner balancing will usually be close enough that a few millimeters of adjustment won’t alter your alignment enough to be noticeable. It’s also important to note that actual weight distribution in the vehicle will always be the most important aspect of a vehicle’s balance – the act of corner balancing is meant to optimize your setup.

So how do you do it?
Once your car is up on some level scales, you’ll have an idea of what your existing corner weights are like, and which corners are heavier/lighter than the rest. The goal is to get each corner to support its fair share of the vehicle’s distributed weight, but the biggest importance is having your diagonal corner balance at 50%, without drastically altering ride height and alignment.
Adding load to a corner is done by raising the ride height of that corner. If you think back to the example of the table with two short diagonally opposed legs, it’s the sample principle as adding length to the short legs. On a car, this is typically done via coilovers, and can be accomplished by adding preload to the springs. It can also be accomplished using coilovers that are adjustable via shock length.
That load (weight) you are adding to the lengthened corners is being alleviated from the opposite diagonal corners. As an example, raising (adding weight to) the Front Right corner will take weight off the Front Left and Rear Right. It will also add some weight to the Rear Left. You can simulate and visualize this process by using a jack to lift one corner of a car – the opposite corner will take on the lifted weight, and you can see this as the body compresses down over that wheel. At the same time, the opposing diagonal will have weight lifted off them, and you’ll see the fender gap increase there.
The goal when corner balancing is to add weight + height to low corners, and remove weight + height from high corners. Always keeping in mind that every adjustment you make will affect all other corners. As a guide:
Raising The Front Right Will:
| Weight: | FR UP | Height: | FR UP |
| FL — | FR ++ | FL + | FR ++ |
| RL ++ | RR — | RL – | RR + |
Keep in mind that the total Front/Rear and Left/Right weight will ALWAYS remain unchanged. To illustrate this, If you add 50lbs to the Front Right, that will, by the laws of physics, also remove 50lbs from the Front Left (to keep the Front weight total the same), and it will also remove 50lbs from the Rear Right (and if you’re paying attention, it will also add 50lbs to the Rear Left)
What’s the Corner Balancing process?
Measuring ride height is the first step. For most track day cars, we’ll measure between the hub to fender – or usually the bottom of the rim to the fender. However, if you have pulled fenders or aftermarket fenders that aren’t very consistent, you may opt to pick different spots to measure ride height from. For example, you may opt to use splitter height for an aerodynamically dependent car.
Don’t get too discouraged if you’re finding it hard to get your ride height absolutely perfect. The 50% diagonal weight balance should be the priority at this stage. Sometimes this is easily done when a car is newer with a fresh, un-abused chassis. Other times, the chassis can be so bent out of shape that fender gaps and ride height can differ quite a lot on the corners. It’s also important to double-check the total vehicle weight between adjustments and measurements to ensure you’re getting an accurate reading and that the scales are placed squarely under each tire. If the measurements are inconsistent, this whole process can be confusing.
On vehicles where it’s impossible to get the ride heights to all be perfect at a 50% cross, generally, you want to balance the difference between the two sides. So on a car with a +6mm FR/RL “banana” – you might aim to be 3mm high on the Front Right, and 3mm high on the Rear Left. Or, in the case of a car with aggressive aerodynamics, keeping the front splitter level to the ground may be a higher priority. In this case, you might opt to make the front level, and have the Rear Left be 6mm high.
You want to make adjustments in small increments. Note that adding 1mm of preload to your spring would typically translate to more than 1mm of height change, but in this case, we are also adding weight to the corner we are raising, so it will end up pretty close to the same height as it was before the adjustment. This means your ride height can measure nearly the same while having a different weight balance after adjustment based on the spread of the weight diagonally. With increments of 1mm, you can also see how an uneven floor could completely mess up every measurement and adjustment from the start, emphasizing the important of level ground for this process.
You should also measure the difference in corner balance and ride height change with the driver in the car. Typically, we expect to have the static ride height of a vehicle 1-3mm higher (depending on spring rate) to compensate for driver weight. This will vary by spring rate, as well as by the specific vehicle. For example, for our in-house racecar 350Z, the driver sits almost directly in the middle of the front and rear wheels, which adds even weight to the left side of the vehicle only, so there is no imbalance in the diagonal weight differences. In many cars, the driver sits forward (or sometimes rearward) of center, which causes more weight on the left/front than the left/rear, and that’s where the imbalance comes from.
It’s worth repeating that large ride height adjustments will change the alignment of a car, just in the same way that large alignment changes could change the car’s corner balancing. This is because changing camber, toe, and caster can actually change the ride height. For this reason it’s best to set the ride height where you want it, align the car and then corner balance it last. Usually, you’ll be close enough that a few mm won’t affect the alignment enough to measure.
Corner Balancing Checklist:
Before starting your corner balancing, make sure that all of these items are covered – or you’ll end up wasting a lot of time!
- Ride height is more or less set to your target height
- Tire pressures are the same all around
- Scales are on a level surface
- Alignment is complete
- Driver weight is in the car (or driver + passenger if you always rip around with a friend)
- Sway bars are disconnected (if there are adjustable endlinks), otherwise, leave the bars connected.
- Scales are not contacting their holders on any sides
- Car is properly rolled out and the suspension is not bound up
- Bounce, bounce the car!

Practical Corner Balancing Example:
Let’s do a few practical examples (theoretical, we’ll update later with actual values) to give you a feel for how this works. When corner balancing, always write down your weight and height next to each other as shown below, along with your changes to ride height to help you keep track of the changes you’ve made and the results for each step.
Corner balancing without hub-stands is a tedious process – so you want to learn the patterns and try to make good guesses to only need a couple of adjustments!
In the example below, you’ll see that there is a 4mm “Banana” – or chassis twist. If we make the front perfectly level side to side, the rear will be 4mm higher on the left. So we’ll aim to split the 2mm difference between the front and the back.
This “Banana factor” is not something you can fix with corner balancing – so don’t waste your time going in circles trying to fix it!
Starting point:
| Weight: | Baseline | Height: | Target 355 | L/R Skew | |
| FL 950 | FR 1050 | Cross 52.5% (2100 / 4000) | FL 355 | FR 357 | 2 Right |
| RL 1050 | RR 950 | Weight: 4000 | RL 356 | RR 354 | 2 Left |
Here we can see that the car is carrying too much load on the Front Right and Rear Left corners, and that the Front Right and Rear Left corners are also too high.
What changes can we make that will help the height and get the cross weight closer? Well, lowering the Front Right and Rear Left will both reduce their weights and get closer to the target ride height.
Lower the Front Right will:
- Decrease the height of the Front Right primarily, as well as the Front Left and Rear Right to a lesser amount
- Decrease the weight of the Front Right and Rear Left
- Increase the weight of the Front Left and Rear Right
- Raise the height of the Rear Left
| Weight: | FR DOWN 2 Turns | Height: | Target 355 | L/R Skew | |
| FL 980 | FR 1020 | Cross 51.0% (2040 / 4000) | FL 354 | FR 355 | 1 Right |
| RL 1020 | RR 980 | Weight: 4000 | RL 356.5 | RR 353.5 | 3 Left |
As we can see here, the heights are closer, but the FR and RL still carry too much weight, and the RL is still too high. Lowering the RL should get us to where we need to be.
Let’s do that now:
| Weight: | RL DOWN 1 TURN | Height: | Target 355 | L/R Skew | |
| FL 1000 | FR 1000 | Cross 50.0% (2000 / 4000) | FL 353.5 | FR 355.5 | 2 Right |
| RL 1000 | RR 1000 | Weight: 4000 | RL 355 | RR 353 | 2 Left |
At this point, we’re pretty well on target. It would be possible to raise the car slightly to get closer to the 355mm target without affecting the corner balancing. There are certain adjustments that you can do that will never affect the corner balancing:
- Raising/lowering both fronts equally will not affect the corner balance
- Raising/lowering both rears equally will not affect the corner balance
- Raising/lowering each side will not affect the corner balance – but this is harder because you must know the motion ratio, and this assumes the anti-roll bar preload can be removed







You must be logged in to post a comment.