Thank you for purchasing our MPP x HEL Ultra Stainless Steel Brake Lines! This is a short instructional guide on installing the brake lines properly. You’ll love the increased pedal feel with these lines, giving your Rivian an even higher end feeling when it comes to stopping power.

NOTE: For safety, only licensed mechanics should be allowed to work on braking and suspension systems.

NOTE: Front and rear bolts have differnt thread pitches. DO NOT CROSS THREAD BOLTS INTO YOUR RIVIAN’S BRAKE CALIPERS!

NOTE: Make sure to use the banjo bolts and new crush washers provided in the kit. Torque spec for the banjo bolt is 12lb-ft. 

Tools & Equipment Required:

  • Brake Fluid
  • Brake Bleeding Kit
  • Socket + Wrench Set
  • Thin Pliers
  • Rubber cap is recommended to reduce brake fluid loss

Installation Instructions:

Start by ensuring the brake fluid reservoir is full. Monitor the level throughout the process, as if a significant amount of fluid is lost the system may ingest some air, making bleeding more difficult. Do not let the reservoir go below the LOW level!

Placing gaffer tape or creating a seal over the brake fluid reservoir can help reduce the amount of brake fluid lost from the system with the lines disconnected.


REAR:

These lines fit similarly to OE lines but with more length. Make sure to clock them to a relaxed and desired angle before tightening any fittings. Make sure to clean up any spilled brake fluid with brake cleaner – as brake fluid is corrosive and will destroy painted surfaces. Torque the banjo-bolt to 12lb-ft.

  • Once the car is jacked or lifted up securely, and the wheel is removed, your first step is to install the new brackets included in your brake kit. The simple flat bracket is for the rear. Ensure the bracket is angled to face upwards and towards the front of the vehicle as shown in the photo below.

MPP Rivian brake line bracket rear

  • With the bracket secure, you can now remove the U-clip that secures the top fitting on the OE brake line. Use a flathead or pliers to push/pull it away from the open end to slide right off.

  • Before removing the OE brake line, you can press the MPP line into the newly installed bracket using the rubber grommet. This might require some force, so push it directly into the bracket and watch your hands so you don’t get pinched! Now the brake line is ready to be swapped over in a timely fashion to lose as little brake fluid as possible.

MPP Rivian brake line bracket with line

  • Remove the fitting from the top of the OE brake line where you removed the U-clip before. At this point, it will start leaking fluid out of the open hard lines on the car, so you can cap it off with a rubber cap to alleviate the mess while you work.
  • At this point, you can remove the OE brake line from the caliper, and secure the MPP line to the caliper with the new banjo bolts provided. There are two different thread banjo bolts in the kit. The coarse-thread banjo bolts are for the rear, and the fine-thread banjo bolts are for the front. 
  • Remove the rubber cap from the OE hardline and secure the top fitting of the MPP line to the Rivian’s hard line.
  • Re-install the U-clip on the top bracket to secure it in place.
  • Lastly, install the brake line clamp included in your kit. Be careful not to overtighten this bolt – it’s just plastic! Be sure to position the clip 2 inches away from the wheel speed sensor boot as shown below

  • Repeat these steps for both sides of the rear.
  • You are now ready to move to the front!

 

FRONT:

The front lines fit a bit differently than stock. Be sure to follow directions carefully, and return the Rivian’s looped ABS line to its original position after installation.  The front install should follow roughly the same steps as the rear, but first, you will want to remove the looped ABS line from its OE bracket and move it slightly to the side.

  • Remove the looped ABS line and move it to the side slightly. Be gentle with this.

Removing Rivian looped ABS brake line

  • Install the MPP provided bracket (look at the OEM bracket, or these pictures to ensure you get the correct side and orientation). Once the bracket is installed, clip in the ABS harness following the OEM routing (AWAY FROM THE WHEEL/TIRE), and clip in the MPP brake line grommet.

  • Remove the U-clip from the top end of the OE brake line.
  • Remove the fitting from the top of the OE brake line where you removed the U-clip before. At this point, it will start leaking fluid out of the open hard lines on the car, so you can cap it off with a rubber cap to alleviate the mess while you work.
  • Remove the OE brake line from the caliper, and secure the MPP line to the caliper with the new banjo bolts provided. There are two different thread banjo bolts in the kit. The coarse-thread banjo bolts are for the rear, and the fine-thread banjo bolts are for the front. 
  • Remove the rubber cap from the OE hardline and secure the top fitting of the MPP line in its place.
  • Re-install the U-clip on that top fitting to secure it in place.
  • Just like that, your lines are installed. Don’t forget to bleed your brakes!

MPP installed Rivian stainless steel brake line

BLEEDING THE BRAKES AND FINISHING UP:

When you are done installing the lines, you’ll need to bleed the brakes. A Licensed Mechanic should have no issues with this procedure, the brakes on the Rivian are just like a standard car. Start from the wheel furthest from the Master Cylinder and work your way forward, RR, LR, RF, LF.

Make sure to double-check the bleeders when you are done and use an Allen key to force out any excess brake fluid sitting in the bleeder screw hole so it doesn’t spill out and stain the caliper.

Once the brakes are bled, press the brake pedal firmly and hold it for 2 minutes. Have someone inspect all fittings for sweating or leaks to confirm the brakes are functioning correctly before driving the vehicle. Make sure to clean any brake fluid off the rotors, and torque the wheels properly.

Inspect your brake lines after a few days of driving to ensure no rubbing is occurring on any wheel speed sensors or brake lines.